StrikeEngine

Car Videos – Calculators – News – Parts – Directory – Insurance

Golf MK7 GTI Big Turbo Selection – 500BHP

Compressed by jpeg-recompress

Another installment of the big turbo selection series. This time we are looking at the VW Golf MK7 GTI and a suitable turbo for 500BHP.

Video summary of this article

MK7 GTI Big Turbo, Step 1 – Finding the VE

As always, we need to find the VE of the engine and to do that we need to find a dyno graph which shows RPM, Power and Boost.

Not the easiest thing to find so I had to use numbers from this. Stage 2 map and numbers from a “road” dyno.

Bolting these numbers in the volumetric efficiency calculator gets this

RPMBoostPowerVE
350021190/2190.88
500022300/3450.96
650017320/3680.91
VE numbers a bit higher than expected, especially at 6500RPM. But we’ll roll with them.

MK7 GTI Big Turbo, Step 2 – Find The Airflow

With the VE number, we can now find our airflow numbers for our boost targets using the turbo calculator.

There is a MK7 GTI here making 35PSI with stock internals so that’s our target.

RPMBoostVE (Italics Adjusted)lbs/minCFMPRPower Est
3500210.88202642.4212
5000350.93435553.38445
6500350.9546983.38560
VE adjusted downwards slightly to be conservative. Power @ flywheel
Bolting the VE numbers and our boost targets into the turbo calculator.

Step 3 – Compressor Analysis

Now we have the data we need to plot points on compressor maps to find a turbo that’s a good fit.

Starting with Gen 2, G25-700

If we are going for more later, then this turbo has some headroom but as it is, looks slightly big, we’ll have to compromise on power at 3000RPM ie reduce the boost, possible down to 7PSI. Not ideal.

Next size down is the Gen 2, G25-585

Too small. Runs out of puff up top.

Going to Gen 1 G Series

Gen1 G25-660

Fits like a glove. But too tight of a glove? Lets see what the next size up looks like.

G30-770 doesn’t have a compressor map, so lets look at the GTX Gen2 turbos.

Gen2 GTX3076R

About the same as the G25-660 but we’ll have to run less boost down low.

So far the G25-660 Gen 1 looks the best. Let’s try one more

Gen 2 GTX3582R

Gen2 G25-700 would be better if we want headroom. 3576 might be better but the compressor map is not on the Garrett website.

Golf MK7 GTI Big Turbo Selection – Conclusion

For 35PSI, Gen1 G25-660 looks the choice. It gets us everything we want with relatively good efficiency. The only downside is if we want to run more boost later. For the road, I think it looks great.

Gen 1 G25-660

If we want some headroom to run more boost later then the Gen2 G25-700 but this is probably only going to give more power 5500RPM plus because more boost lower in the RPM range is limited by the surge line.

For the road I think the Gen 1 G25-660, for drag then possibly the Gen 2 G25-700 is better.

The 21 PSI ask at 3000RPM is really making selection difficult, if you’re prepared to sacrifice response for more top end it open us the possibility of using the older gen turbos. Out boost and RPM targets in this article is having our cake and eating it.

If your happy to compromise low down for max power and you want something cheaper, the Gen 2 GTX3582R and Gen2 GTX3076R look a good fit.

Note, this is not all of the Garrett turbos available because some don’t have the correct compressor map listed next to them.

Exhaust Diameter

With regards to exhaust diameter.

As always, for the downpipe, I’d go as big as possible. 100mm if it will fit, at least for the first 30cms downstream of the turbo.

With regards to the rest of the exhaust system, using the exhaust diameter calculator, 3-3.5 inches should work, personally I’d go 3.5 if it fits, to be on the safe side. Exhaust speed is getting close to the limit at 3 inches.

Explore StrikeEngine

Find performance parts on ebay




This page was last modified Oct 26, 2026 @ 11:22 pm

StrikeEngine TV Highlights

Comments:

Your email address will not be published. Required fields are marked *

11 + 1 =



Get our news in your inbox - Subscribe

* indicates required